We have stumbled on the article on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround down the page on the internet and think it made sense to share it with you in this article.
Installing a bath tub isn't precisely rocket science, yet it does require solid plumbing, carpentry, and also in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently obtainable, the task can move easily; if you have to open up a wall surface to remove the old bathtub and also position the new bath tub, the task is much harder. In either situation, the job is within a residence handyman's skills, although you will need a helper to leave the old bathtub and also embeded in the new one. Make sure you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a service provider to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Possibilities are you may need an expert plumber to make tube links.
This article will certainly aid you install a new tub in your restroom if you have already acquired a brand-new bathtub and also do not need to change the arrangement of your previous supply of water pipes.
Your devices and product list must make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you need to do is separate the water system. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing taps can be rather bothersome as a result of the limited accessibility that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a fabric prepared for the remaining water that will originate from the pipes. Once the supply pipes have actually been removed, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old securing substance.
Before going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier provided backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind ought to be attached to the tap finishes first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Using the two wooden boards under its feet, put the tub in the needed setting. The wood boards are practical in evenly spreading the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and also readjusting the feet on the bath tub up until the spirit level reads degree.
To set up taps, fit the bottom of the outermost versatile tap adapter to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
Activate the water as well as examine all joints and also brand-new pipework for leakages and tighten them if essential. Fill the bath tub and likewise check the overflow outlet and also the normal outlet for leakages.
Finally, repair the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub must wait until the bath tub has been made use of at least when as this will certainly settle it into its final placement.
Planning for the Setup
Firstly, the sustaining frame provided with the bath needs to be fitted (if needed) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you use every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final position.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can move enough to break a rigid seal, causing the water to penetrate the wall surface in between the bath and also the tiling, resulting in complications with moisture and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are sold in tubes as well as cartridges, and also can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to securing, to allow for the movement experienced when the bathtub remains in use. The sealant can break relatively early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently offered on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were made aware of that report about How to Install a Bathtub through a friend on our other domain. Liked our entry? Please share it. Let somebody else find it. I am grateful for your time. Come back soon.
Schedule A Free Estimate